{"product_id":"electrocookie-mini-pc-case-for-raspberry-pi-5-with-m-2-nvme-ssd-pcie-hat-and-active-rgb-lighting-cooler-black-case-m-2-hatx1001-2-black-case-m-2-hat-x1001","title":"ElectroCookie Mini PC Case for Raspberry Pi 5 with M.2 NVMe SSD PCIe HAT and Active RGB Lighting Cooler (Black Case + M.2 HAT[X1001]) 2. Black Case + M.2 HAT (X1001)","description":"\u003ch3\u003eElectroCookie Mini PC Case for Raspberry Pi 5 with M.2 NVMe SSD PCIe HAT and Active RGB Lighting Cooler (Black Case + M.2 HAT[X1001])\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eRaspberry Pi 5 NVMe SSD HAT – Compatibility Notice This NVMe SSD HAT for\nRaspberry Pi 5 shares the same circuit design as widely adopted M.2 HATs,\nfeaturing a PCB layout that’s been minimally customized to fit our case\ndimensions. As with the official Raspberry Pi Foundation M.2 HAT, it supports\nonly 2230 and 2242 NVMe SSDs. If your SSD is not recognized or fails to boot\nwith the Raspberry Pi 5, it is most likely due to incompatibility between the\nSSD and the Raspberry Pi 5. The HAT simply acts as a signal and power bridge\nand does not affect SSD compatibility. SSD controllers known to cause issues\ninclude: SMI2263XT, SMI2263EN, MAP1202, Phison series controllers ★ Known\nIncompatible SSDs ★ The following SSDs have been reported to show\ncompatibility issues with Raspberry Pi 5: Inland TN446Corsair MP600Micron\n2450Kingston OM8SEP4256Q-A0WD_Blue SN550 \/ SN580WD_Green SN350WD_Black SN850 \/\nSN770Kingspec seriesAny other SSDs that use SMI2263XT, SMI2263EN, MAP1202, or\nPhison series controllers ★ Recommended SSDs (Confirmed Compatible) ★ The\nfollowing SSDs are known for low power consumption and low heat generation,\nmaking them a great match for the Raspberry Pi 5’s hardware and power limits:\nSamsung PM9A1, PM981, PM991, PM991a, PM9B1SK hynix BC901, BC711Official\nRaspberry Pi NVMe SSD ★ Tips for Stable Operation ★ Make sure your Raspberry\nPi 5’s bootloader and OS are up to date.Before purchasing an SSD, we recommend\nsearching online for “Pi Benchmarks” to check real-world performance and\ncompatibility reports. 🔧 How to Set Up SSD Boot on Raspberry Pi 5 Using an M.2\nHAT 📝 Note: SSD boot setup is the same as with the official M.2 HAT or other\nstandard models. You can follow the official Raspberry Pi documentation,\nonline tutorials, or simply refer to the step-by-step guide below. 1. Assemble\nyour Raspberry Pi 5 board with the M.2 HAT and SSD. 2. Insert an SD card with\nRaspberry Pi OS into your Raspberry Pi 5, and power it on. 3. Open the\nterminal and run the following commands one by one to update your Raspberry\nPi.: sudo apt update \u0026amp;\u0026amp; sudo apt full-upgrade sudo apt install rpi-eeprom sudo\nrpi-eeprom-update 4. Install Raspberry Pi Imager: sudo apt install rpi-imager\n5. Launch Raspberry Pi Imager: rpi-imager 6. In the Imager: - Select Raspberry\nPi 5 as your device - Choose the OS version - Select your SSD as the target\ndrive, and start the installation. 7. After OS installation, run the following\nto configure boot order: sudo raspi-config 8. Set boot order: Advanced Options\n→ Boot Order → NVMe\/USB Boot Then press Finish or the Escape key. 9. Reboot\nyour Raspberry Pi. It will now boot from the NVMe SSD 🎉\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n  \u003cul class=\"a\"\u003e\n         \u003cli\u003eMiniature PC-Style Case for Raspberry Pi 5, featuring an NVMe M.2 SSD shield compatible with 2230, 2242, 2260, and 2280 sizes, providing expanded storage and ultra-fast responsiveness.\u003c\/li\u003e\n         \u003cli\u003e**SSD Compatibility \u0026amp; Setup Info : Please check SSD compatibility in the product description or by searching Pi Benchmark online. Boot drive setup instructions are also provided in the product description below, or you can follow official Raspberry Pi documentation and online tutorials.\u003c\/li\u003e\n         \u003cli\u003eEnjoy easy access to GPIO pins and quick SSD swaps with the tinted side door, which also beautifully showcases internal RGB lighting to combine style with functionality.\u003c\/li\u003e\n         \u003cli\u003eEquipped with an RGB-lit PWM fan that turns on with system power and automatically adjusts its speed based on CPU temperature (*Note: The lighting is not programmable, and the fan may not spin when the CPU is cool, or may run continuously if no OS or bootable drive is available to control it.).\u003c\/li\u003e\n         \u003cli\u003eEasily power your Raspberry Pi 5 on or off from outside the case using the convenient side power button, directly connected to the Raspberry Pi 5's power button.\u003c\/li\u003e\n         \u003cli\u003eCreate a unique case by customizing front panels; the frame is designed to support various materials like 1\/161\/8 inch(1.63mm) acrylic, wood, and PCB board for a personalized style.\u003c\/li\u003e\n  \u003c\/ul\u003e","brand":"ElectroCookie","offers":[{"title":"2. Black Case + M.2 HAT (X1001)","offer_id":48936786133145,"sku":"B0DWMKSBWT","price":188.0,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0491\/3148\/7385\/files\/B0DWMKSBWT.jpg?v=1787724598","url":"https:\/\/soundstores.net\/products\/electrocookie-mini-pc-case-for-raspberry-pi-5-with-m-2-nvme-ssd-pcie-hat-and-active-rgb-lighting-cooler-black-case-m-2-hatx1001-2-black-case-m-2-hat-x1001","provider":"SoundStore Australia","version":"1.0","type":"link"}