{"product_id":"etepon-digital-oscilloscope-kit-with-bnc-clip-cable-probe-with-power-supply-assembled-finished-machine-em001-black-1","title":"ETEPON Digital Oscilloscope Kit with BNC-Clip Cable Probe with Power Supply, (Assembled Finished Machine) EM001 Black-1","description":"\u003ch3\u003eETEPON Digital Oscilloscope Kit with BNC-Clip Cable Probe with Power Supply, (Assembled Finished Machine) EM001\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eETEPON Digital Oscilloscope Kit 2.4” TFT Adapter Added\nVersion Thanks for some customers' advice, we have updated this oscilloscope\nand added a suitable adapter for it. Package： 1 Oscilloscope 1 BNC-clip\ncable 1 Users Manual 1 A Power Adapter Advanced Features No need do assembly\nor soldering work Easily Measuring Professional Assembly Detailed Instruction\nSensitivity Extended Handheld Rotary Encoder Added Read more ETEPON Digital\nOscilloscope Kit Kindly Note This oscilloscope runs on 9V power adapter. The\npower supply voltage must not exceed 10V. Otherwise it is possible to burn out\nthe machine. 9v dc power supply should be center positive.Resistor values can\neasily be misinterpreted. It is highly recommended to check their values via\nan ohmmeter before soldering them to the board.Make sure you know the polarity\nand orientation of all parts. Read more Sensitivity Extended The sensitivity\nof the EM001 has been extended both in width and height, which is wider and\nwider than the others. It reaches 5mV \/ div - 20V \/ div, while others is only\n10mV \/ div - 5v \/ div. Rofessional Assembled Display and MCU are mounted on\nthe same board (mainboard) to avoid using inter-board pin-headers. Analog\nchannel is placed on a separated board which contains most user install parts,\nso the analog and digital circuits can be better separated. Rotary Encoder It\nhas been added the rotary encoder, makes parameter adjustment quicker and\neasier. Read more Hand-Held This updated digital oscilloscope can be hand-\nheld, while the others can only be used by placing it on the desktop.\nMeasuring Easily Using the Auto\/Normal\/Single Trigger mode,it is easy to\ncapture instantaneous waveform. Hold Function You can freeze waveform display\nat any time.And with waveform storage function you will not lose the waveform\nafter power off. Read more Specification Number of Channel 1 Analog Bandwidth\n0 - 200KHz Sensitivity 5mV\/Div - 20V\/Div Sensitivity Error \u0026lt; 5% Resolution\n12-bit Input Impedance 1M ohm Maximum Input voltage 50Vpk Coupling DC, AC, GND\nTrigger Modes Auto, Normal, Single Trigger Types Rising\/falling edge Trigger\nPosition 1\/2 of buffer size fixed Display 2.4 inch color TFT LCD with 320 x\n240 resolution Power Supply 9V DC (8 - 10V acceptable) Dimension 115mm X 75mm\nX 22mm Weight 100 gram Answers for Frequently Asked Questions to help you: Q1,\nDisplay white screen? A1: Power supply voltage must be in the range of 8 -\n10V.； Confirm signal input within range of equipment parameters. Q2,trigger\nlevel not center trigger level? A2: Hold down [TRIGGER] button for about 3\nseconds. This will set the trigger level to the medium value of signal\namplitude. Q3: Why my voltage numbers are incorrect? A3: There are two\npossible causes for wrong voltage display. 1 ) The reference point has not\nbeen calibrated, and 2 ) the gain of analog channel is incorrect. For 1 ) you\njust need to perform VPos alignment as instructed in the manual (it is\nstrongly suggested to do factory default restore before VPos alignment to make\nsure all parameters are valid). For 2 ) please refer to the Troubleshooting\nsection below to find out possible causes in analog channel. Q4: Can I use DSO\nShell to measure high voltages like AC 220V ? A4: This oscilloscope was\ndesigned for low voltage measurement. The maximum input voltage was specified\nas 50Vpk (peak value). So it can not be used to directly measure any voltage\nhigher than 50V. Otherwise that could damage the device or even cause body\ninjury. But if attenuator is used it is possible to use oscilloscope to\nmeasure voltages higher than 50V. Using a standard probe at 10X setting, for\nexample, it can take voltage up to 400V. However users need to fully\nunderstand the potential risk before doing so and will do at his\/her own risk.\nstrongly discourages users to use it for measurements at voltages higher than\nspecified. Seller will assume no responsibility for any damages, losses, or\nbody injuries caused by using DSO Shell to measure voltages higher than\nspecification. Q5: Why does the encoder knob rotate trigger level up and down\nwithout change? A5: The encoder knob of the equipment needs to be fine-tuned\nin design, so it needs to be adjusted slowly to work. When the speed is too\nfast, the device will be considered invalid. If you have any question on using\nthis oscilloscope, please feel free to contact with us!\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n  \u003cul class=\"a\"\u003e\n         \u003cli\u003eSIMPLE DESIGNETEPOPN EM001 oscilloscope kit is an assembled finished machine that can be used directly to avoid assembly\/soldering process problems and saving you a lot of time. The display and MCU are mounted on the same board (motherboard) to avoid the use of inter-board pinouts. The analog channels are placed on a separate board containing most user-installed parts, thus allowing better separation of analog and digital circuits.\u003c\/li\u003e\n         \u003cli\u003eUPGRADED VERSIONThe sensitivity of the EM001 oscilloscopes has been extended both in width and height which is wider and higher than the others It reaches 5mV \/ div - 20V \/ div while the others is only 10mV \/ div - 5v \/ div.\u003c\/li\u003e\n         \u003cli\u003eHAND-HELDThis updated digital oscilloscope can be hand-held while the others can only be used by placing it on the desktop.\u003c\/li\u003e\n         \u003cli\u003eROTARY ENCODERIt has been added the rotary encoder makes parameter adjustment more quicker and easier.\u003c\/li\u003e\n         \u003cli\u003eWHAT YOU GETYou will get an assembled mini oscilloscope, BNC clip cable, and a power supply. Detailed operating instructions (troubleshooting guide) and schematics are also provided. If you have any questions about this digital oscilloscope, you can always contact us and we will reply within 24 hours.\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003chr class=\"py-vbody\" style=\"display: none\"\u003e\n\n\n","brand":"ETEPON","offers":[{"title":"Default Title","offer_id":42519213965465,"sku":"B081ZPMKJ5","price":250.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0491\/3148\/7385\/products\/B081ZPMKJ5.jpg?v=1661271213","url":"https:\/\/soundstores.net\/products\/etepon-digital-oscilloscope-kit-with-bnc-clip-cable-probe-with-power-supply-assembled-finished-machine-em001-black-1","provider":"SoundStore Australia","version":"1.0","type":"link"}